![]() ![]() I've posted all the details, including a picture of the 3D-printed ring, at is definitely as difficult as they say. However, the results were disappointing, with various issues, I became discouraged, Covid happened, and I haven't really done anything on it since February. The 3D printing expert didn't really look at any of my attempts, he just started from a blank page, created a cylinder, then merged with part of a stretched-sphere shared hole. I took what I had into the Makerspace, together with the taped together white ring, and a white ball. I tried various ways, with different starting points, but none were satisfactory. Also, the outer edge isn't straight either, it tapers toward the base that may not be crucial but probably DOES help prevent the ring falling down the hole. The complexity arises because of the way the inner surface is shaped, it isn't straight down, the ring is thinner at the top than at the bottom, and the curve is convex. In 3D modelling terms, it seems fairly simple. I started learning how to use Tinkercad, and Fusion 360, and then tried to create a model of a ring. someone emailed me yesterday asking if I had made any progress - thanks Anthony! Thanks in advance for any info and/or help anyone may be able to provide. I have posted some text and pictures on a web page at Table-top Russian Billiards table. If the 3D route works, then I would probably go for a full set of nine so I have spares. Sav mentioned when he approved my registration, that you have had some success with 3D printing rings for standard tables might it be 'easy' to scale those models to a smaller size? My immediate need is for 2 rings, if different colours are possible then they would be one white and one red. I have found many sites online selling a set of red plastic rings made by Perador but I don't think they will fit my table, as they are described as "Inner diameter of 55mm - Outer diameter of 66mm" the rings I have have an outer diameter of c 47.5 mm at the top, and an inner diameter of less than 1.5 inches (the size of the balls). I have been looking to find replacement rings for the re-assembled white and the missing red ones but without success. Also, the red ring is completely missing! One of the white rings broke into pieces and has been taped back together, but the hole is now slightly too small for the ball to pass through freely so we have to play without it. The glue on the rings has solidified over the years and they have become loose I have re-glued most of the ones we have. ![]() The pockets have wooden rings, which are of different colours: white (10, 20, 30), yellow (50), black (100) and red (200). If there was a D marked on the baize at the start position, it must have faded. The leather(?) covering at the baulk end is triangular rather than rectangular. There are 3 red mushrooms, which are usually placed in front of the 50 and 200 holes, although faint chalk crosses on the baize near the 100 hole suggest that mushrooms may have been placed on either side of that hole at times. The rubber in the cushions has gone hard over time, and there is no give. The baize is slightly 'moth-eaten' in places, but not enough to spoil the play. The table is not in pristine condition but it is good enough for our current level of skill, and we enjoy playing. ![]() The score values of the holes are marked in gold on the top of the wood surround, and on the top edge of back of the chute tray. The baize area of the table is 4ft x 2 ft, it has the full complement of 9 holes (10, 20x2, 30x2, 50x2, 100, 200), arranged in the usual positions. I have looked online but have not come across anything remotely similar apart from in an old thread on the British Bar Billiards forum ( Table-top Bar Billiards) which mentions sightings on ebay and Youtube of various-sized table-top tables. age, manufacturer, etc if anyone here can help. I don't know exactly how old it is, as there is no date or maker's mark on it that I can see I remember playing on it in the 60s when the family lived in Leicester so it is at least 50-something years old! i would like to know more about it. It was always referred to as a 'Russian Billiards' table rather than a 'Bar Billiards' table. ![]() I have recently resumed, after decades of the table being propped against a wall, using a very old table-top Russian Billiards table. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |